Epson ActionPrinter 4500 Скачать руководство пользователя

Страница: 235 / 317

Options

Problem

Solution

Using an optional

interface, the printer

does not operate
properly (continued).

The printer does not

print or the printout is
not what you expected

(continued).

You may be trying to use an interface with

the wrong specification. Check the
specifications to make sure that you can
use the interface with this printer.

You may be trying to use a cable with the
wrong specification. Make sure that the

cable matches the specifications of the

interface.

The DIP switches or jumpers on the
interface board may be set wrong. See the

interface manual for the correct settings.

The interface settings on the computer may
be wrong. See your computer manual for

the correct settings.

The computer and interface settings may
not match. Match the settings for each

condition.

Two cables may be installed on the printer;

only one cable may be attached at any
time.

Troubleshooting

7-33

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды