Epson ActionPrinter 4500 Скачать руководство пользователя страница 204

Страница: 204 / 317

Problems and Solutions

This chapter discusses problems you may encounter while operating
your printer and their likely solutions. If you are having difficulty

achieving the desired printing result, first locate the problem in the table
below and then see the appropriate page for the solution.

Power supply

Power is not being supplied.

Printing

The printer does not print.

The print is faint or uneven.

Dots are missing in the printed characters or
graphics.

Printed characters are not what you expected.

The print position is not what you expected.

See 7-4

See 7-5

See 7-6

See 7-7

See 7-8

See 7-11

Paper handling

Single sheets do not feed properly.

Continuous paper does not feed properly.

Switching between single sheets and continuous
paper cannot be performed properly.

The short tear-off function does not operate
properly.

See 7-14

See 7-17

See 7-21

See 7-23

7-2

Troubleshooting

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Бренды по названию

Популярные бренды