Epson ActionPrinter 4500 Скачать руководство пользователя

Страница: 212 / 317

Printing

Problem

Solution

Printed characters are

not what you expected

(continued).

The characters printed
are smaller than
expected.

The typestyle selected

by SelecType is not
printed.

Characters cannot be
defined using ESC &
and ESC :

The condensed mode may be set. Check to

see if the

CONDENSED

light on the control

panel is on. If it is lit, press the

CONDENSED

button to cancel the mode.

Also, if your application program is

capable of sending control codes, you can
cancel the condensed mode by sending the
DC2 code to the printer. See Chapter 9.

The software may not be properly installed
for your printer. Use the program’s setup

(or install) procedure to check the printer

settings and reset as needed.

Your software may be overriding your

SelecType setting. If your program allows

you to change the printing style, software

control will override the SelecType
settings. For these application programs use
the program, not SelecType, to change

typestyles.

User-defined character mode may not be

selected. When defining characters, make
sure that DIP switch 2-5 is set to off.

7-10

Troubleshooting

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды