Epoke SKE Series, Инструкция по эксплуатации

Страница: 7 / 29

5
epoke
®
SKE8-12-15-20
GB-0305.1 epoke
®
2.0.3.4 Thermal hazard
Thermal Hazard - not applicable.
2.0.3.5 Hazard caused by noise
A noise measurement has not been carried out as the noi-
se pollution depends on the used vehicle.
2.0.3.6 Hazard caused by vibrations
Vibration measurement is omitted - not relevant.
2.0.3.7 Hazard caused by radiation
Radiation measurement is omitted - not relevant.
2.0.3.8 Hazard caused by materials and substances
Demounting (scrapping): Is to be carried out by a environ-
mental acknowledged scrap merchant.
2.1 Safety measures
2.1.1 General safety measures
All EPOKE spreaders and equipment can be
operated by one person. Spread is controlled
entirely from the driver’s cab.
Instruction
- The owner of the carrying vehicle undertakes
to ensure that the spreader is used only by people who:
• know the basic safety regulations and are thoroughly
familiar with the operation of the spreader
•
have read and understood the section on safety and the
warnings in the technical documentation.
Instruction - Everyone who is authorised to work with the
spreader undertakes:
•
to familiarise themselves with the basic safety regulations.
•
to read and understand the section on safety and the
warnings in the technical documentation.
Instruction
- only trained and instructed personnel are
permitted to work with the spreader:
•
The authorisation of the personnel for starting, operating,
maintenance and repair must be clearly defined.
• Personnel in training may only work with the spreader
under the supervision of an experienced person.
Instruction - The spreader is designed with the safety
regulations in mind. Even so, the life of the driver may be
at risk while the machine is in use.
The spreader may only be used for its intended purpose
and in the proper condition as regards safety equipment.
Out of consideration for safety, the following is to be
observed:
Before operation the operator is to check whether devices
for control, safety and protection are correctly fitted and ok.
If defects are noted on safety devices or when other de-
fects are noted which have influence on the safe
operation of the machine, there cannot be any operation
until these defects have been repaired.
Correction of flaws, maintenance and repairs are only to
be carried out, when the machine is not in operation.
After maintenance or repairs, the safety devices are to be
correctly placed.
2.1.2 Reference to permitted total weight
SKE8
Permitted total weight . . . . . . . . . . . . . . . . . . . . . 1200 kg
Permitted axle load . . . . . . . . . . . . . . . . . . . . . . . 1000 kg
Supporting load on draweye . . . . . . . . . . . . . . . . .200 kg
Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 kg
SKE12
Permitted total weight . . . . . . . . . . . . . . . . . . . . 1500 kg
Permitted axle load . . . . . . . . . . . . . . . . . . . . . . . 1200 kg
Supporting load on draweye . . . . . . . . . . . . . . . . 300 kg
Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 kg
SKE15
Permitted total weight . . . . . . . . . . . . . . . . . . . . . 2660 kg
Permitted axle load . . . . . . . . . . . . . . . . . . . . . . . 1210 kg
Supporting load on draweye . . . . . . . . . . . . . . . . . 560 kg
Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 kg
SKE20
Permitted total weight . . . . . . . . . . . . . . . . . . . . 3500 kg
Permitted axle load . . . . . . . . . . . . . . . . . . . . . . 2800 kg
Supporting load on draweye . . . . . . . . . . . . . . . . 750 kg
Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720 kg