ENSTROM 280FX Series Скачать руководство пользователя страница 79

Страница: 79 / 246

ENSTROM 280FX OPERATOR’S MANUAL

4-15

FAA Approved: Jul 27/15

Rev. 10

Report No. 28-AC-020

Apr 15/15

6. When rotor RPM reaches 100 RPM, fully engage clutch.

NOTE

The clutch disengage warning light will go out
and the rotor RPM warning light will come on
when the clutch is fully engaged.

7. Place clutch handle in stowed position.

WARNING

Severe engine damage and complete loss of

power to rotor system will result if the manual
clutch is disengaged under any condition other
than throttle at idle position.

4-10. Operational Checks

NOTE

Mixture and RPM adjustments may be required

for change in base altitude.

1. Advance throttle to 1800 RPM and wait for cylinder head

temperature to reach 200

2. After reaching 200

F cylinder head temperature, slowly

advance throttle to 2300 RPM and wait until oil
temperature reads 80

3. Advance throttle to 3050 RPM. Low rotor RPM warning

light should go out at 334 rotor RPM (2900 engine RPM).

4. Check fuel flow 65-70 lb/hr (engine cold) (50-65 lb/hr

engine warm).

a. Adjust the fuel flow as required to attain 50-70

lbs/hr (as required) at full RPM (thus raising
EGT/TIT and reducing manifold pressure.)

5. Check manifold pressure 16-18 inches.

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Содержание 280FX Series























































































































































































































































Результаты поиска

Содержание 280FX Series

Отзывы:

Похожие инструкции для 280FX Series

Бренды по названию

Популярные бренды

ENSTROM 280FX Series, Руководство оператора

Результаты поиска

Содержание 280FX Series

Отзывы:

Похожие инструкции для 280FX Series

Бренды по названию

Популярные бренды