ENSTROM 280FX Series Скачать руководство пользователя страница 157

Страница: 157 / 246

ENSTROM 280FX OPERATOR’S MANUAL

8-23

Rev. 6

Report No. 28-AC-020

Feb 21/12

Figure 8-2. Autorotation RPM Schedule for 6000 Ft Base

Altitude

Example:

RPM checked passing through 8000 ft pressure altitude. OAT
at this altitude: 42

F (6

C); Density altitude is 8800 ft;

Aircraft weight when RPM was checked: 2060 lb.

* Autorotation RPM should be 374 with collective full down.

Check RPM in steady 60 MPH autorotation with the collective
full down. Record pressure altitude (altimeter set to 29.92),

OAT, rotor RPM, and aircraft weight.

Do not exceed 385 RPM or drop below 332 RPM.

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Содержание 280FX Series























































































































































































































































Результаты поиска

Содержание 280FX Series

Отзывы:

Похожие инструкции для 280FX Series

Бренды по названию

Популярные бренды

ENSTROM 280FX Series, Руководство оператора

Результаты поиска

Содержание 280FX Series

Отзывы:

Похожие инструкции для 280FX Series

Бренды по названию

Популярные бренды