background image

 Ensemble Commissioning: Installer Toolkit Communications 

 

© 2020 Enphase Energy Inc. All rights reserved. 

July 24, 2020 

___________Installer Initials: All steps complete on this page 

8

G.3.1. Grid profile will be updated. 
G.3.2. Tariff will be updated only if the single rate was set in step E. 
G.3.3. PV microinverters will be provisioned. 
G.3.4. Enpower will be provisioned. 
G.3.5. Encharge microinverters will be provisioned. 

G.3.5..1.1  During provisioning, the status flows as follows: 

G.3.5..1.1.1  Discovered / not discovered (Installer Toolkit is able to 

discover the device using Bluetooth Low Energy (BLE). 

G.3.5..1.2.1  Waiting for provisioning (The initial communication is being 

established. Installer Toolkit is sending network information to 
Encharges and Enpower using BLE). 

G.3.5..1.3.1  Waiting for acknowledgement (Envoy is trying to 

communicate to the Encharges and Enpower using the wireless 
2.4 GHz radio). 

G.3.5..1.4.1  Provisioned (Envoy can communicate with the Encharges 

and Enpower). 

G.3.5..2.1  Once provisioning is complete, click 

Done

.  

 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
H.  Confirm that the Encharge batteries are communicating with the Envoy by checking Installer 

Toolkit step 2: 

Device & Array

. Encharge batteries should display “communicating” as 

follows: 

Содержание Ensemble













Отзывы: