EnGenius ECB3500 Скачать руководство пользователя

Страница: 91 / 117

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

Transmit Power

: You may have the different application distance of the device by

selecting a value from the drop-down list. This feature can be helpful in restricting the
coverage area of the wireless network.

Fragment

: Packets over the specified size will be fragmented in order to improve

performance on noisy networks.

RTS Threshold

: Packets over the specified size will use the RTS/CTS mechanism to

maintain performance in noisy networks and preventing hidden nodes from
degrading the performance.

Protection Mode

: If your wireless network is using both 802.11b and 802.g devices

then it is recommended to enable this feature so that the 802.11b devices will not
degrade the performance of 802.11g devices.

Click on the

Apply

button to save the changes.

8.6 Management

Click on the

Management

link on the

navigation  drop-down  menu.  You  will  then
see  six  options:  administration,  SNMP
settings,  backup/restore  settings,  firmware
upgrade, time settings, and log. Each option
is described below.

8.6.1 Administration

Click on the

Administration

link under the

Management

menu. This option allows

you to create a user name and password for the device. By default, this device is
configured without a user name and password

admin

. For security reasons it is

highly recommended that you create a new user name and password.

Содержание ECB3500






















































































































Результаты поиска

Содержание ECB3500

Отзывы:

Похожие инструкции для ECB3500

Бренды по названию

Популярные бренды

EnGenius ECB3500, Руководство пользователя

Результаты поиска

Содержание ECB3500

Отзывы:

Похожие инструкции для ECB3500

Бренды по названию

Популярные бренды