EnGenius ECB3500 Скачать руководство пользователя | Manualshive

Страница: 85 / 117

background image

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

85

8.4.1.3

WAN – PPPoE

The WAN interface can be configured as PPPoE. This type of connection is usually
used for a DSL service and requires a username and password to connect.

Internet Connection Type

: Select

PPPoE

from the drop-down list.

MTU

: The Maximum Transmission Unit (MTU) is a parameter that determines the

largest  packet  size  (in  bytes)  that  the  router  will  send  to  the  WAN.  If  LAN  devices
send  larger  packets,  the  router  will  break  them  into  smaller  packets.  Ideally,  you
should set this to match the MTU of the connection to your ISP. Typical values are
1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE connection. If the
router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU  is  set  too  low,  the  router  will  fragment  packets  unnecessarily  and  in  extreme
cases  may  be  unable  to  establish  some  connections.  In  either  case,  network
performance can suffer.

Login

: Specify the user name which is provided by your ISP.

Password:

Specify the password which is provided by your ISP, and then verify it

once again in the next field.

Service Name

: Specify the name of the ISP.

Type

: Select a reconnection type:

Keep Alive

(A connection to the Internet is

always maintained),

Connect on Demand

: You have to open up the Web-based

management interface and click the

Connect

button manually any time that you wish

to connect to the Internet.

«
...
83
84
85
86
87
...
»

Содержание ECB3500






















































































































Отзывы:

Нет отзывов

Похожие инструкции для ECB3500

Бренд: Planet Страницы: 41

Бренд: NETGEAR Страницы: 92

Бренд: ZyXEL Communications Страницы: 2

ConnectPort X2e Wi-Fi

Бренд: Digi Страницы: 2

Бренд: Exibel Страницы: 2

Бренд: Linksys Страницы: 49

Бренд: Linksys Страницы: 70

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 38

Бренд: Abocom Страницы: 2

Бренд: EnGenius Страницы: 58

Бренд: EnGenius Страницы: 67

Бренд: EnGenius Страницы: 64

Бренд: EnGenius Страницы: 86

Бренд: Ubiquiti Страницы: 15

Бренд: IPone Страницы: 45

Бренд: Icom Страницы: 119

Бренд: Laird Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды