EnGenius ECB3500 Скачать руководство пользователя

Страница: 69 / 117

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

Spanning Tree Status

: Choose to enable or disable the spanning tree feature.

Bridge Hello Time

: Specify the number of seconds for the hello time.

Bridge Max Age

: Specify the number of seconds for the max age.

Bridge Forward Delay

: Specify the number of seconds for the bridge forward delay.

Priority

: Specify the number of seconds for the priority.

Click on the

Apply

button to save the changes.

7.4 Wireless

Click on the

Wireless

link on the

navigation  drop-down menu.  You  will  then
see  four  options:  wireless  network,
wireless  security,  wireless  MAC  filter,  and
wireless advanced settings. Each option is
described below.

7.4.1 Wireless Network

The

Wireless Network

page allows you to configure the wireless mode, channel,

SSID, and security settings.

Содержание ECB3500






















































































































Результаты поиска

Содержание ECB3500

Отзывы:

Похожие инструкции для ECB3500

Бренды по названию

Популярные бренды

EnGenius ECB3500, Руководство пользователя

Результаты поиска

Содержание ECB3500

Отзывы:

Похожие инструкции для ECB3500

Бренды по названию

Популярные бренды