EnGenius ECB3500 Скачать руководство пользователя | Manualshive

Страница: 84 / 117

background image

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

84

Internet Connection Type

: Select the

Static IP

from the drop-down list.

Account Name

: Specify an account name if your ISP has provided you with one.

Domain Name

: Specify a domain name if the ISP has provided you with one.

MTU

: The Maximum Transmission Unit (MTU) is a parameter that determines the

largest  packet  size  (in  bytes)  that  the  router  will  send  to  the  WAN.  If  LAN  devices
send  larger  packets,  the  router  will  break  them  into  smaller  packets.  Ideally,  you
should set this to match the MTU of the connection to your ISP. Typical values are
1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE connection. If the
router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU  is  set  too  low,  the  router  will  fragment  packets  unnecessarily  and  in  extreme
cases  may  be  unable  to  establish  some  connections.  In  either  case,  network
performance can suffer.

IP Address:

Specify the IP address for this device, which is assigned by your ISP.

Subnet Mask:

Specify the subnet mask for this IP address, which is assigned by

your ISP.

Default Gateway:

Specify the IP address of the default gateway, which is assigned

by your ISP.

Domain Name Service

: Select

Get Automatically from ISP

if the ISP will provide

the DNS address, if not, select

Use these DNS servers

and specify the primary and

secondary DNS server IP address.

Router MAC Address

: If you need to change the MAC address of the router’s WAN

interface, either type in an alternate MAC address (for example, the MAC address of
the router initially connected to the ISP) or click on the

Clone

MAC button.

Click on the

Apply

button to save the changes.

«
...
82
83
84
85
86
...
»

Содержание ECB3500






















































































































Отзывы:

Нет отзывов

Похожие инструкции для ECB3500

3CRWE51196 - OfficeConnect Wireless Cable/DSL...

Бренд: 3Com Страницы: 6

Бренд: Caimore Страницы: 83

Barricade SMCWBR14S-N3

Бренд: SMC Networks Страницы: 106

Бренд: Sophos Страницы: 4

Бренд: DIGITAL YACHT Страницы: 6

Бренд: Zte Страницы: 29

Бренд: Pakedge Device & Software Страницы: 57

Juplink RX4-1500

Бренд: Vanin Страницы: 2

Бренд: DQ Technology Страницы: 43

Бренд: u-blox Страницы: 36

Бренд: AirLive Страницы: 51

Бренд: LG Innotek Страницы: 14

Бренд: Laird Страницы: 40

Бренд: RFNet Страницы: 40

SimpleLink CC3135MOD

Бренд: Texas Instruments Страницы: 69

Бренд: Intellinet Страницы: 41

Бренд: Intellinet Страницы: 51

Бренд: Intellinet Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды