EnGenius ECB3500 Скачать руководство пользователя | Manualshive

Страница: 102 / 117

background image

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

102

9.4.1.2

WAN – Static IP

The  WAN  interface  can  be  configured  as  Static  IP  address.  In  this  type  of
connection,  your  ISP  provides  you  with  a  dedicated  IP  address  (which  does  not
change as DHCP).

Internet Connection Type

: Select the

Static IP

from the drop-down list.

Account Name

: Specify an account name if your ISP has provided you with one.

Domain Name

: Specify a domain name if the ISP has provided you with one.

MTU

: The Maximum Transmission Unit (MTU) is a parameter that determines the

largest  packet  size  (in  bytes)  that  the  router  will  send  to  the  WAN.  If  LAN  devices
send  larger  packets,  the  router  will  break  them  into  smaller  packets.  Ideally,  you
should set this to match the MTU of the connection to your ISP. Typical values are
1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE connection. If the
router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU  is  set  too  low,  the  router  will  fragment  packets  unnecessarily  and  in  extreme
cases  may  be  unable  to  establish  some  connections.  In  either  case,  network
performance can suffer.

IP Address:

Specify the IP address for this device, which is assigned by your ISP.

«
...
100
101
102
103
104
...
»

Содержание ECB3500






















































































































Отзывы:

Нет отзывов

Похожие инструкции для ECB3500

EnOcean TALK MODUL G2

Бренд: Waldmann Страницы: 68

RailBox 11ac/WiFi 5

Бренд: Acksys Страницы: 36

DECT 1615 Series

Бренд: Uniden Страницы: 28

Бренд: Ubiquiti Страницы: 33

Бренд: Loopcomm Страницы: 40

Бренд: Zte Страницы: 29

Бренд: FCCID Страницы: 90

Бренд: LevelOne Страницы: 27

Бренд: Comcast Страницы: 16

Бренд: SkyLink Страницы: 61

Бренд: Intellinet Страницы: 3

Бренд: Intellinet Страницы: 63

Бренд: Intellinet Страницы: 84

Бренд: Sapido Страницы: 108

3CRWE554G72T - OfficeConnect Wireless 11g Cable/DSL...

Бренд: 3Com Страницы: 146

Бренд: Zte Страницы: 17

Бренд: Pakedge Device & Software Страницы: 46

Бренд: Flybox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды