EnGenius ECB3500 Скачать руководство пользователя | Manualshive

Страница: 104 / 117

background image

11b/g Wireless Long Range Multi-function 7+1 AP

Version 1.2

104

MTU

: The Maximum Transmission Unit (MTU) is a parameter that determines the

largest  packet  size  (in  bytes)  that  the  router  will  send  to  the  WAN.  If  LAN  devices
send  larger  packets,  the  router  will  break  them  into  smaller  packets.  Ideally,  you
should set this to match the MTU of the connection to your ISP. Typical values are
1500 bytes for an Ethernet connection and 1492 bytes for a PPPoE connection. If the
router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU  is  set  too  low,  the  router  will  fragment  packets  unnecessarily  and  in  extreme
cases  may  be  unable  to  establish  some  connections.  In  either  case,  network
performance can suffer.

Login

: Specify the user name which is provided by your ISP.

Password:

Specify the password which is provided by your ISP, and then verify it

once again in the next field.

Service Name

: Specify the name of the ISP.

Type

: Select a reconnection type:

Keep Alive

(A connection to the Internet is

always maintained),

Connect on Demand

: You have to open up the Web-based

management interface and click the

Connect

button manually any time that you wish

to connect to the Internet.

Domain Name Server

: Select

Get Automatically from ISP

if the ISP will provide

the DNS address, if not, select

Use these DNS servers

and specify the primary and

secondary DNS server IP address.

Click on the

Apply

button to save the changes.

9.4.2 VPN Pass Through

Click on the

VPN Pass Through

link under the

Router

drop-down menu. This page

allows you to enable the pass through feature.

PPTP Pass Through

: Place a check in this box if you would like to enable this pass

through. PPTP is a protocol (set of communication rules) that allows corporations to
extend their own corporate network through private "tunnels"

L2TP Pass Through

: Place a check in this box if you would like to enable this pass

through. Layer 2 Tunneling Protocol is a transport protocol that enables tunneling
through the Internet for the establishment of virtual private networks.

IPSec Pass Through

: Place a check in this box if you would like to enable this pass

through. IPSec is a VPN protocol used to implement secure exchange of packets at
the IP layer.

«
...
102
103
104
105
106
...
»

Содержание ECB3500






















































































































Отзывы:

Нет отзывов

Похожие инструкции для ECB3500

Бренд: Telit Wireless Solutions Страницы: 48

Бренд: Inseego Страницы: 68

Бренд: Airlink101 Страницы: 134

Бренд: Netis Страницы: 16

Бренд: AMTC Страницы: 81

Бренд: Loopcomm Страницы: 94

Бренд: Linksys Страницы: 69

Бренд: Linksys Страницы: 140

Бренд: Ruckus Wireless Страницы: 58

Бренд: Nortel Страницы: 144

Бренд: Westermo Страницы: 28

Бренд: CAMBRIDGE Страницы: 28

Бренд: Black Box Страницы: 59

Бренд: 3Com Страницы: 4

Бренд: Solwise Страницы: 3

Бренд: Solwise Страницы: 39

Бренд: Ebyte Страницы: 21

Бренд: Ebyte Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды