Endress+Hauser Liquiline To Go Ex CYM291 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

background image

13

Start-Up

Inserting the Batteries

With four AA batteries, the Liquiline To Go
Ex CYM291 has an operating time of
approx. 500 h.
Open the battery compartment on the
rear of the device. Be sure to observe the
correct polarity when inserting the batter‑
ies (see markings in the battery chamber).
Close the battery compartment cover and
screw it handtight.

Check the shipment for transport damage and completeness (see Package
Contents).

NOTICE!
Do not operate the device when one of the following conditions applies:
•  the device shows visible damage
•  the device fails to perform the intended function
•  prolonged storage at temperatures above 70 °C
•  severe transport stresses
In this case, a professional routine test must be performed.
This test should be carried out at our factory.

Precautions for application in hazardous locations

WARNING!
• Only open the battery compartment of the Liquiline To Go Ex CYM291

outside the hazardous location.

• Never try to open the device. If a repair should be required, return the

device to our factory.

• Never use the USB port within the hazardous location.

«
...
11
12
13
14
15
...
»

Содержание Liquiline To Go Ex CYM291

































































Отзывы:

Нет отзывов

Похожие инструкции для Liquiline To Go Ex CYM291

Бренд: X-Rite Страницы: 80

Бренд: Keithley Страницы: 49

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: 4iiii Страницы: 3

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: ICS Schneider Messtechnik Страницы: 40

Бренд: Palstar Страницы: 15

Бренд: KALEAS Страницы: 64

Бренд: Xtralis Страницы: 13

Бренд: Tektronix Страницы: 124

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Бренд: PASCO Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды