Endress+Hauser Liquiline To Go Ex CYM291 Скачать руководство пользователя страница 43

Страница: 43 / 64

Oxy Cond

Error Messages

The following error messages can be shown in the display.

Message

Cause

Remedy

blinks Battery empty

Replace batteries

ERROR 1

Value out of range

Check whether the measurement
conditions correspond to the adjusted
measuring range.

ERROR 2

ORP value out of range

ERROR 3

Temperature value out of
range

ERROR 4

Zero point too high/low

Thoroughly rinse the sensor and recal-
ibrate. If this does not help, replace the
sensor.

ERROR 5

Slope too high/low

ERROR 6

Cell constant too high/low

Enter nominal cell constant or calibrate
the sensor using a known solution.

ERROR 8

Calibration error:
Identical buffers

Use a buffer solution with a different
nominal value before starting the next
calibration step.

ERROR 9

Calibration error:
Buffer unknown

Make sure that you use the same
buffer set as configured.

ERROR 10

Calibration media
interchanged

Repeat calibration.

ERROR 11

Measured value unstable
Stability criterion not met

Leave the sensor in the liquid until the
temperature is stable. If this does not
help, replace the sensor.

ERROR 14

Time and date invalid

Set time and date

ERROR 18

Configuration invalid

Restart, reset to factory settings,
configure and calibrate. If this does not
help, send in the device for repair.

ERROR 19

Factory settings error

Device defective, send it in.

ERROR 21

Sensor error
(Memosens)

Connect operational Memosens
sensor.

ERROR 22

Sensor conflict

Connect only one sensor.

Error and Status Messages

Содержание Liquiline To Go Ex CYM291

































































Результаты поиска

Содержание Liquiline To Go Ex CYM291

Отзывы:

Похожие инструкции для Liquiline To Go Ex CYM291

Бренды по названию

Популярные бренды

Endress+Hauser Liquiline To Go Ex CYM291, Руководство по эксплуатации

Результаты поиска

Содержание Liquiline To Go Ex CYM291

Отзывы:

Похожие инструкции для Liquiline To Go Ex CYM291

Бренды по названию

Популярные бренды