Endress+Hauser Liquiline System CAT860 Скачать руководство пользователя страница 36

Страница: 36 / 44

Technical data

Liquiline System CAT860

Hauser

14.3

Performance characteristics

14.3.1 Type of sampling

Control unit, Liquiline System CA80 analyzer

14.3.2 Filtrate quantity

• 5.5 to 16.5 ml/min
• Factory setting: 8.25 ml/min

All the values have been determined with new filters.

14.3.3 Suction height of peristaltic pump

Max. 5 m (16 ft)

14.3.4 Hose length, filter to pump

Max. 5 m (16 ft)

14.3.5 Hose length, pump to analyzer

Max. 30 m (98 ft)

14.4

Environment

14.4.1 Ambient temperature range

Unheated
• 5 to 50

C (41 to 122

Heated
• -20 to 50

C (-4 to 122

14.4.2 Storage temperature

-20 to 60

C (-4 to 140

14.4.3 Humidity

10 to 95%, not condensating

14.4.4 Degree of protection

IP55

14.4.5 Pollution degree

The product is suitable for pollution degree 2.

Содержание Liquiline System CAT860













































Результаты поиска

Содержание Liquiline System CAT860

Отзывы:

Похожие инструкции для Liquiline System CAT860

Бренды по названию

Популярные бренды

Endress+Hauser Liquiline System CAT860, Руководство по эксплуатации

Результаты поиска

Содержание Liquiline System CAT860

Отзывы:

Похожие инструкции для Liquiline System CAT860

Бренды по названию

Популярные бренды