Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 87

Страница: 87 / 210

Proline Promag P 500 HART

Operation options

Hauser

Access is via:

• HART protocol

• CDI-RJ45 service interface →  84

• WLAN interface→  84
Typical functions:

• Configuring parameters of transmitters

• Loading and saving device data (upload/download)

• Documentation of the measuring point

• Visualization of the measured value memory (line recorder) and event logbook

For additional information about FieldCare, see Operating Instructions BA00027S

and BA00059S

Source for device description files

See information →  90

Establishing a connection

1. Start FieldCare and launch the project.
2. In the network: Add a device.

 The

Add device

window opens.

3. Select the

CDI Communication TCP/IP

option from the list and press

to confirm.

4. Right-click

CDI Communication TCP/IP

and select the

Add device

option in the

context menu that opens.

5. Select the desired device from the list and press

to confirm.

 The

CDI Communication TCP/IP (Configuration)

window opens.

6. Enter the device address in the

IP address

field: 192.168.1.212 and press

Enter

confirm.

7. Establish the online connection to the device.

For additional information, see Operating Instructions BA00027S and BA00059S

Содержание Hart Proline Promag P 500



















































































































































































































Результаты поиска

Содержание Hart Proline Promag P 500

Отзывы:

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 87 / 210

Результаты поиска

Содержание Hart Proline Promag P 500

Отзывы: