manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 39 / 210

Поделиться
Скачать
Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 39

Proline Promag P 500 HART

Electrical connection

Hauser

39

Relay output

Standard installation cable is sufficient.

Current input 0/4 to 20 mA

Standard installation cable is sufficient.

Status input

Standard installation cable is sufficient.

Cable diameter

• Cable glands supplied:

M20 × 1.5 with cable ⌀ 6 to 12 mm (0.24 to 0.47 in)

• Spring-loaded terminals: Suitable for strands and strands with ferrules.

Conductor cross-section 0.2 to 2.5 mm

2

 (24 to 12 AWG).

Choice of connecting cable between the transmitter and sensor

Depends on the type of transmitter and the installation zones

2

3

B

1

3

A

1

3

A

1

3

A

1

3

A

2

3

B

4

5

6

  A0032477

1

Proline 500 digital transmitter

2

Proline 500 transmitter

3

Promag sensor

4

Non-hazardous area

5

Hazardous area: Zone 2; Class I, Division 2

6

Hazardous area: Zone 1; Class I, Division 1

A

Standard cable to 500 digital transmitter →   39
Transmitter installed in the non-hazardous area or hazardous area: Zone 2; Class I, Division 2 / sensor
installed in the hazardous area: Zone 2; Class I, Division 2 or Zone 1; Class I, Division 1

B

Signal cable to 500 transmitter →   40
Transmitter and sensor installed in the hazardous area: Zone 2; Class I, Division 2 oder Zone 1;
Class I, Division 1

A: Connecting cable between sensor and transmitter: Proline 500 – digital
Standard cable

A standard cable with the following specifications can be used as the connecting cable.

Содержание Hart Proline Promag P 500



















































































































































































































Отзывы:

Нет отзывов