Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 124

Страница: 124 / 210

Commissioning

Proline Promag P 500 HART

124

Hauser

Parameter

Prerequisite

Description

Selection / User

entry

Factory setting

Separator

A local display is provided.

Select decimal separator for
displaying numerical values.

• . (point)
• , (comma)

. (point)

Backlight

One of the following
conditions is met:
• Order code for "Display;

operation", option

"4-line,

illum.; touch control"

• Order code for "Display;

operation", option

"4-line,

illum.; touch control
+WLAN"

Switch the local display
backlight on and off.

• Disable
• Enable

Enable

Visibility depends on order options or device settings

10.5.5 Performing electrode cleaning

The

Electrode cleaning circuit

submenu contains parameters that must be configured for

the configuration of electrode cleaning.

The submenu is only available if the device was ordered with electrode cleaning.

Navigation

"Setup" menu → Advanced setup → Electrode cleaning circuit

‣

Electrode cleaning circuit

ECC duration

ECC recovery time

ECC cleaning cycle

ECC Polarity

Parameter overview with brief description

Parameter

Prerequisite

Description

Selection / User

entry / User

interface

Factory setting

Electrode cleaning circuit

For the following order code:
"Application package", option

"ECC electrode cleaning"

Enable the cyclic electrode
cleaning circuit.

• Off
• On

Off

ECC duration

For the following order code:
"Application package", option

"ECC electrode cleaning"

Enter the duration of electrode
cleaning in seconds.

0.01 to 30 s

2 s

ECC recovery time

For the following order code:
"Application package", option

"ECC electrode cleaning"

Define recovery time after
electrode cleaning. During this
time the current output values
will be held at last valid value.

1 to 600 s

60 s

Содержание Hart Proline Promag P 500



















































































































































































































Результаты поиска

Содержание Hart Proline Promag P 500

Отзывы:

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 124 / 210

Результаты поиска

Содержание Hart Proline Promag P 500

Отзывы: