manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 38 / 210

Поделиться
Скачать
Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 38

Electrical connection

Proline Promag P 500 HART

38

Hauser

7  

Electrical connection

NOTICE

The measuring device does not have an internal circuit breaker.

‣

For this reason, assign the measuring device a switch or power-circuit breaker so that

the power supply line can be easily disconnected from the mains.

‣

Although the measuring device is equipped with a fuse, additional overcurrent

protection (maximum 10 A) should be integrated into the system installation.

7.1  

Connection conditions

7.1.1  

Required tools

• For cable entries: Use corresponding tools

• For securing clamp: Allen key 3 mm

• Wire stripper

• When using stranded cables: crimper for wire end ferrule

• For removing cables from terminal: Flat blade screwdriver ≤ 3 mm (0.12 in)

7.1.2  

Requirements for connecting cable

The connecting cables provided by the customer must fulfill the following requirements.

Electrical safety

In accordance with applicable federal/national regulations.

Protective ground cable

Cable: 2.1 mm

2

 (14 AWG)

The grounding impedance must be less than 1 Ω.

Permitted temperature range

• The installation guidelines that apply in the country of installation must be observed.

• The cables must be suitable for the minimum and maximum temperatures to be

expected.

Power supply cable

Standard installation cable is sufficient.

Signal cable

Current output 4 to 20 mA HART

A shielded cable is recommended. Observe grounding concept of the plant.

Current output 0/4 to 20 mA

Standard installation cable is sufficient.

Pulse/frequency/switch output

Standard installation cable is sufficient.

Double pulse output

Standard installation cable is sufficient.

Содержание Hart Proline Promag P 500



















































































































































































































Отзывы:

Нет отзывов