Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 210

Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 148

Diagnostics and troubleshooting

Proline Promag P 500 HART

148

Hauser

Error

Possible causes

Solution

Network connection not present or
unstable

WLAN network is weak.

• Operating device is outside of

reception range: Check network
status on operating device.

• To improve network

performance, use an external
WLAN antenna.

Parallel WLAN and Ethernet
communication

• Check network settings.
• Temporarily enable only the

WLAN as an interface.

Web browser frozen and operation
no longer possible

Data transfer active

Wait until data transfer or current
action is finished.

Connection lost

1. Check cable connection and
power supply.
2. Refresh the Web browser and
restart if necessary.

Content of Web browser
incomplete or difficult to read

Not using optimum version of Web
server.

1. Use the correct Web browser
version .
2. Clear the Web browser cache and
restart the Web browser.

Unsuitable view settings.

Change the font size/display ratio
of the Web browser.

No or incomplete display of
contents in the Web browser

• JavaScript not enabled
• JavaScript cannot be enabled

1. Enable JavaScript.
2. Enter http://XXX.XXX.X.XXX/
basic.html as the IP address.

Operation with FieldCare or
DeviceCare via CDI-RJ45 service
interface (port 8000)

Firewall of computer or network is
preventing communication

Depending on the settings of the
firewall used on the computer or in
the network, the firewall must be
adapted or disabled to allow
FieldCare/DeviceCare access.

Flashing of firmware with FieldCare
or DeviceCare via CDI-RJ45 service
interface (via port 8000 or TFTP
ports)

Firewall of computer or network is
preventing communication

Depending on the settings of the
firewall used on the computer or in
the network, the firewall must be
adapted or disabled to allow
FieldCare/DeviceCare access.

12.2 Diagnostic information via light emitting diodes

12.2.1 Transmitter

Proline 500 – digital

Different LEDs in the transmitter provide information on the device status.

«
...
146
147
148
149
150
...
»

Содержание Hart Proline Promag P 500



















































































































































































































Отзывы:

Нет отзывов