manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 144 / 210

Поделиться
Скачать
Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 144

Operation

Proline Promag P 500 HART

144

Hauser

Assign channel 4

→   145

Logging interval

→   145

Clear logging data

→   145

Data logging

→   145

Logging delay

→   145

Data logging control

→   145

Data logging status

→   145

Entire logging duration

→   145

‣

Display channel 1

‣

Display channel 2

‣

Display channel 3

‣

Display channel 4

Parameter overview with brief description

Parameter

Prerequisite

Description

Selection / User

entry / User

interface

Factory setting

Assign channel 1

The 

Extended HistoROM

application package is
available.

The software options
currently enabled are
displayed in the

Software option
overview

 parameter.

Assign a process variable to
logging channel.

• Off
• Volume flow
• Mass flow
• Corrected volume

flow

• Flow velocity
• Conductivity

 *

• Corrected

conductivity

 *

• Temperature

 *

• Electronic

temperature

• Current output 1
• Current output 2

 *

• Current output 3

 *

• Current output 4

 *

Off

Assign channel 2

The 

Extended HistoROM

application package is
available.

The software options
currently enabled are
displayed in the

Software option
overview

 parameter.

Assign process variable to
logging channel.

Picklist, see 

Assign

channel 1

 parameter

(→   144)

Off

Содержание Hart Proline Promag P 500



















































































































































































































Отзывы:

Нет отзывов