manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Руководство по эксплуатации, Страница: 173 / 210

Поделиться
Скачать
Endress+Hauser Hart Proline Promag P 500 Скачать руководство пользователя страница 173

Proline Promag P 500 HART

Accessories

Hauser

173

15  

Accessories

Various accessories, which can be ordered with the device or subsequently from Endress

+Hauser, are available for the device. Detailed information on the order code in question is

available from your local Hauser sales center or on the product page of the

Hauser website: 

www.endress.com

.

15.1   Device-specific accessories

15.1.1   For the transmitter

Accessories

Description

Transmitter
• Proline 500 – digital
• Proline 500

Transmitter for replacement or storage. Use the order code to define the following
specifications:
• Approvals
• Output
• Input
• Display / operation
• Housing
• Software

• Proline 500 – digital transmitter:

Order code: 5X5BXX-XXXXXXXXXA

• Proline 500 transmitter:

Order code: 5X5BXX-XXXXXXXXXB

Proline 500 transmitter for replacement:
It is essential to specify the serial number of the current transmitter when
ordering. Based on the serial number, the device-specific data (e.g.,
calibration factors) of the replacement device can be used for the new
transmitter.

For details
• Proline 500 – digital transmitter: Installation Instructions EA01151
• Proline 500 transmitter: Installation Instructions EA01152

External WLAN antenna

External WLAN antenna with 2 m (6.6 ft)connecting cable and two angle brackets.
Order code for "Enclosed accessories", option 

P8

 "Wireless antenna wide area".

Further information on the WLAN interface →   84.

Pipe mounting set

Pipe mounting set for transmitter.

• Proline 500 – digital transmitter

Order number: 71346427

• Proline 500 transmitter

Order number: 71346428

Protective cover
Transmitter
• Proline 500 – digital
• Proline 500

Is used to protect the measuring device from the effects of the weather: e.g.
rainwater, excess heating from direct sunlight.

• Proline 500 – digital transmitter

Order number: 71343504

• Proline 500 transmitter

Order number: 71343505

For details, see Installation Instructions EA01160

Display guard
Proline 500 – digital

Is used to protect the measuring device from the effects of the weather: e.g.
rainwater, excess heating from direct sunlight.

Order number: 71228792

For details, see Installation Instructions EA01161

Ground cable

Set, consisting of two ground cables for potential equalization.

Содержание Hart Proline Promag P 500



















































































































































































































Отзывы:

Нет отзывов