Endress+Hauser Cerabar PMP51B Скачать руководство пользователя страница 15

Страница: 15 / 60

Cerabar PMP51B Analog

Mounting

Hauser

Mounting

5.1

Mounting requirements

5.1.1

General instructions

• Do not clean or touch process membrane with hard and/or pointed objects

• Do not remove process membrane protection until shortly before installation

Always firmly tighten the housing cover and the cable entries.

1. Counter-tighten the cable entries.
2. Tighten the coupling nut.

5.1.2

Installation instructions

• The standard devices (without diaphragm seals) are mounted according to the same

guidelines as pressure gauges (DIN EN837-2)

• To ensure optimal readability of the local display, adjust the housing and local display

• Hauser offers a mounting bracket to mount the device on pipes or walls

• Use flushing rings for flanges, flange seals and pancake seals if buildup or clogging can

be expected at the process membrane

• The flushing ring is clamped between the process connection and the flange, flange

seal or pancake seal

• Material buildup in front of the process membrane is flushed away and the pressure

chamber is vented via the two lateral flushing holes

• When measuring in media containing solids (e.g. dirty liquids), installing separators and

drain valves is useful for capturing and removing sediment

• Using a valve manifold allows for easy commissioning, installation and maintenance

without interrupting the process

• When mounting the device, establishing the electrical connection and during operation:

prevent the penetration of moisture into the housing

• Point the cable and plug downwards as much as possible to prevent moisture from

entering (e.g. rainwater or condensation)

5.1.3

Installation instructions for thread

• Device with G 1 ½" thread:

Place the flat seal on the sealing surface of the process connection

Avoid additional strain on the process membrane: do not seal the thread with hemp or

similar materials

• Device with NPT thread:

• Wrap Teflon tape around the thread to seal it

• Tighten the device at the hexagon bolt only; do not turn it by the housing

• When screwing in, do not overtighten the thread; tighten the NPT thread to the

required depth according to the standard

• For the following process connections, a tightening torque of max. 40 Nm (29.50 lbf ft)

is specified:

• Thread ISO228 G ½" with flush membrane

• Thread DIN13 M20 x 1.5 with flush membrane

• NPT 3/4" with flush membrane

Содержание Cerabar PMP51B





























































Результаты поиска

Содержание Cerabar PMP51B

Отзывы:

Похожие инструкции для Cerabar PMP51B

Бренды по названию

Популярные бренды

Endress+Hauser Cerabar PMP51B, Руководство по эксплуатации

Результаты поиска

Содержание Cerabar PMP51B

Отзывы:

Похожие инструкции для Cerabar PMP51B

Бренды по названию

Популярные бренды