Endress+Hauser Analytik Jena multi EA 5000 Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 186

background image

Specifications

multi EA 5000

184

17.8 Standards and directives

Protection class and protection
type

The device is protection class I. The housing is protection type IP 20.

Device safety

The device complies with the following safety standards

¡

EN 61010-1

¡

EN 61010-2-081

¡

EN 61010-2-010

EMC compatibility

The device has been checked for transient emissions and noise immunity.

It meets the requirements for transient emissions according to

¡

EN 61326-1 (EN 55011 group 1, class B)

The device meets the requirements for noise immunity according to

¡

EN 61326-1 (requirements for use in a basic environment)

Environmental compatibility

The device has been tested for environmental compatibility and meets the requirements
according to

¡

ISO 9022-2

¡

ISO 9022-3

EU directives

The device meets the requirements of the directive 2011/65/EU.

The device is designed and tested in accordance with standards meeting the require-
ments of EU directives 2014/35/EU and 2014/30/EU. The device leaves the factory in a
sound condition with regard to technical safety. To maintain this condition and to en-
sure safe operation, the user must strictly observe the safety and operating instructions
contained in this operating manual. For accessories delivered with the device and sys-
tem components from other manufacturers, the information provided in their respective
operating manuals has priority.

Guidelines for China

The device contains substances subject to regulation (according to the directive
"Management Methods for the Restriction of the Use of Hazardous Substances in Electrical
and Electronic Products"). Analytik Jena AG guarantees that, if the device is used as in-
tended, these substances will not leak within the next 25 years and therefore will not
pose a threat to the environment or health within this time period.

«
...
182
183
184
185
186
»

Содержание Analytik Jena multi EA 5000



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Analytik Jena multi EA 5000

Бренд: Parker Research Corp Страницы: 3

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 16

Бренд: Keller Страницы: 6

Бренд: Keithley Страницы: 32

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: i-SENS Страницы: 50

Бренд: Fly Henry Страницы: 5

Бренд: Magtrol Страницы: 76

Бренд: Flexim Страницы: 160

Бренд: Neriox Страницы: 10

Бренд: Hanna Instruments Страницы: 15

Бренд: horiba Страницы: 10

Бренд: Kabelmat Страницы: 27

RLACS277RLACS29

Бренд: Racelogic Страницы: 10

Бренд: A&D Страницы: 2

Бренд: Rinstrum Страницы: 2

Бренд: Sagola Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды