Endress+Hauser Analytik Jena multi EA 5000 Скачать руководство пользователя страница 39

Страница: 39 / 186

multi EA 5000

Operation

Sample

Furnace installation po-
sition and sampling

Comment

AOX

Horizontal for

ABD

ABD with MMS

Column method:
Activated carbon in a
quartz container in a
quartz glass boat

Batch method:
Activated carbon with no
quartz container in a
quartz glass boat with
holding-down clamp

EC/OC

Horizontal for

ABD

ABD with MMS

Filter in a quartz glass
boat with hold-down
clamp

TC, TOC, NPOC in water

Vertical for

MMS 5000

or manual sampling

TIC in water

Vertical (manual sam-
pling)

Direct injection in the TIC
reactor

Gas, non-pressurized

Horizontal or vertical
for

GSS module

with ABD (horizontal)

For trace analysis: Verti-
cal + GSS module recom-
mended

Gas, pressurized

Horizontal or vertical
for

GSS/LPG combi module

GSS module with
GSS adapterbox

with ABD (horizontal)

LPG

Horizontal or vertical

GSS/LPG combi module

LPG module 2.0

with ABD (horizontal)

For trace analysis: Verti-
cal +
GSS/LPG combi module
recommended

6.3

Switching on the basic module and the modules

Before switching on the basic module, always check:

The other components (detection modules, sampling modules, PC) are connected to
the basic module.

The gas supply is connected in accordance with instructions. The inlet pressure is ex-
actly 600 kPa (6 bar).

The samples have been prepared.

Switch on the basic module as follows:

}

Open the valves at the pressure reducers of the gas supply.

}

Switch on all required components (detection modules, sampling modules, PC).

}

Switch on the basic module via the power switch.

Содержание Analytik Jena multi EA 5000



























































































































































































Результаты поиска

Содержание Analytik Jena multi EA 5000

Отзывы:

Похожие инструкции для Analytik Jena multi EA 5000

Бренды по названию

Популярные бренды

Endress+Hauser Analytik Jena multi EA 5000, Руководство по эксплуатации

Результаты поиска

Содержание Analytik Jena multi EA 5000

Отзывы:

Похожие инструкции для Analytik Jena multi EA 5000

Бренды по названию

Популярные бренды