Emerson Rosemount 5900C Скачать руководство пользователя

Страница: 250 / 322

•

The dual compartment transmitter housing, with electronics and cabling separated,
can be replaced without opening the tank

•

It is protected against lightning, moisture/rain, and has a surface protection against
sulphur and salt spray atmospheres

•

Electronics consists of one encapsulated units.

•

No need for re-calibration

A.6

Environment

A.6.1

Ambient operating temperature

-40 to +70 °C (-40 to +158 °F). Minimum start-up temperature is -50 °C (-58 °F)

A.6.2

Storage temperature

-50 to +85 °C (-58 to +185 °F)

A.6.3

Humidity

0-100% relative humidity

A.6.4

Ingress protection

IP 66/67 and NEMA

A.6.5

Vibration resistance

IEC 60770-1 level 1 and IACS UR E10 test 7

A.6.6

Telecommunication

Compliance with:

•

FCC 15B Class A, and 15C

•

RED (EU directive 2014/53/EU) ETSI EN 302372; EN 50371

•

IC (RSS210-5)

A.6.7

Electromagnetic compatibility

•

EMC (EU directive 2014/30/EU) EN 61326-1; EN 61326-3-1

•

OIML R85:2008

Specifications and reference data

Reference Manual

September 2019

00809-0100-5901

250

Reference Manual

Содержание Rosemount 5900C



































































































































































































































































































































Результаты поиска

Содержание Rosemount 5900C

Отзывы:

Похожие инструкции для Rosemount 5900C

Бренды по названию

Популярные бренды

Emerson Rosemount 5900C, Справочное руководство

Результаты поиска

Содержание Rosemount 5900C

Отзывы:

Похожие инструкции для Rosemount 5900C

Бренды по названию

Популярные бренды