Emerson Rosemount 5900C Скачать руководство пользователя

Страница: 213 / 322

Backing up multiple device configurations using
TankMaster

™

Using Rosemount TankMaster WinSetup to save configuration for multiple devices:

Procedure

1. Start the Rosemount TankMaster WinSetup program.
2. In the

WinSetup

workspace window select the

Devices

folder.

3. Click the right mouse button and choose the

Save Database of All to Files

option.

This option is also available from the

Service/Devices

menu.

4. Select a device from the

Available Devices

pane and press the

Add

button in order to

move it to the

Selected Devices

pane. Repeat for all devices you wish to include.

5. Choose the

Holding Registers

and

Predefined Registers

options (the User-Defined

option should only be used for advanced service).

6. Click the

Browse

button, select a folder and type a name for the backup file.

7. Click the

Start

button to save the database backup.

The backup file can be viewed as a text file in any word processing program:

Reference Manual

Service and troubleshooting

00809-0100-5901

September 2019

Rosemount 5900C Radar Level Gauge

213

Содержание Rosemount 5900C



































































































































































































































































































































Результаты поиска

Содержание Rosemount 5900C

Отзывы:

Похожие инструкции для Rosemount 5900C

Бренды по названию

Популярные бренды

Emerson Rosemount 5900C, Справочное руководство

Результаты поиска

Содержание Rosemount 5900C

Отзывы:

Похожие инструкции для Rosemount 5900C

Бренды по названию

Популярные бренды