manualshive.com logo in svg

Emerson Rosemount 2240S, Справочное руководство, Страница: 96 / 194

Поделиться
Скачать
Emerson Rosemount 2240S Скачать руководство пользователя страница 96

86

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

Maintenance required alerts

A Maintenance required alert indicates that the device or some part of the device needs maintenance 
soon. If the condition is ignored, the device will eventually fail. There are five parameters associated with 
FD_MAINT_ALM, they are described below.

FD_MAINT_MAP

The FD_MAINT_MAP parameter contains a list of conditions indicating that the device or some part of 
the device needs maintenance soon. The priority is not the same as the MAINT_PRI parameter described 
below. It is hard coded within the device and is not user configurable.

Note that maintenance alarms are not enabled by default for the Rosemount 2240S.

Below is a list of the conditions:

1. Auxiliary Device Measurement Close to Limit

FD_MAINT_MASK

The FD_MAINT_MASK parameter will mask any of the failed conditions listed in FD_MAINT_MAP. A bit 
on means that the condition is masked out from alarming and being broadcast to the host through the 
alarm parameter.

FD_MAINT_PRI

FD_MAINT_PRI designates the alarming priority of the FD_MAINT_ALM, see 

“Alarm priority” on page 78

. 

The default is 0 and the recommended values are 3 to 7.

FD_MAINT_ACTIVE

The FD_MAINT_ACTIVE parameter displays which of the conditions is active.

FD_MAINT_ALM

An alarm indicating that the device needs maintenance soon. If the condition is ignored, the device will 
eventually fail.

Содержание Rosemount 2240S



































































































































































































Отзывы:

Нет отзывов