Emerson Rosemount 2240S Скачать руководство пользователя страница 163

Страница: 163 / 194

153

Product Certifications

October 2017

Reference Manual

00809-0100-2240, Rev DA

B.14 Custody Transfer

Australia Custody Transfer

Certificate: No 5/1/7

Standards: Regulation 60: National Measurement

Regulations 1999

Belgium Custody Transfer

BMS Certificate: NR. P6.0.014.01-B-12

Croatia Custody Transfer

Certificate: 558-02-01_01-15-2

Czech Republic Custody Transfer

Certificate: 0111-CS-C022-10

Estonia Custody Transfer

Certificate: TJA 6.13-3_15.09.11

France Custody Transfer

Certificate: No. LNE-24609

Germany Custody Transfer

Certificate: PTB-1.5-4058175 (Rosemount Tank Gauging
system)

India Custody Transfer

Certificate: IND/13/12/191

Indonesia Custody Transfer

Certificate: DITJEN MIGAS CT approval 26.10.2010

Italy Custody Transfer

Certificate: 183349 (Rosemount Tank Gauging system)

Malaysia Custody Transfer

Certificate: ATS 09-11

Netherlands Custody Transfer

NMI Certificate: TC7982

Norway Custody Transfer

Certificate: No. N-11-7146

Poland Custody Transfer

Certificate: ZT-7 2013

Portugal Custody Transfer

Certificate: P12_101.12_31

Serbia Custody Transfer

Certificate: 393-7_0-01-2088

South Africa Custody Transfer

Certificate: SAEx S11-065

Switzerland Custody Transfer

Certificate: Zulassungszertifikat CH-L-11127-01

Russia Custody Transfer

GOST Pattern Approval

Certificate:
SE.C.29.004.A No. 46866 (5900S),
SE.C.29.004.A No. 49065 (Rosemount Tank Gauging system)

Kazakhstan Custody Transfer

GOST Pattern Approval

OIML Custody Transfer

Certificate: R85-2008-SE-11.01

B.15 Approval Drawings

Follow the installation guidelines presented in Factory Mutual
system control drawings in order to maintain certified ratings for
installed devices.

The following drawings are included in the documentation for the
Rosemount 2240S Multi-Input Temperature Transmitter:



9240040-910 System Control Drawing

for hazardous location

installation of intrinsically safe FM-US and FM-C approved
apparatus



9240040-976 System Control Drawing

for hazardous location

installation of intrinsically safe FM ATEX and FM IECEx approved
apparatus

Electronic copies of the system control drawings can also be found
on the “Manuals & Drawings” CD ROM that is shipped with the
Rosemount 2240S Multi-Input Temperature Transmitter.

Содержание Rosemount 2240S



































































































































































































Результаты поиска

Содержание Rosemount 2240S

Отзывы:

Emerson Rosemount 2240S, Справочное руководство, Страница: 163 / 194

Результаты поиска

Содержание Rosemount 2240S

Отзывы: