manualshive.com logo in svg

Emerson Rosemount 2240S, Справочное руководство, Страница: 68 / 194

Поделиться
Скачать
Emerson Rosemount 2240S Скачать руководство пользователя страница 68

58

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

Figure 5-7. Measurement range and geometry parameters

A. Upper Sensor Limit (100%)

B. Lower Sensor Limit (0%)

C. Upper measurement Limit

D. Measurement range

E. Lower measurement Limit

F. Tank Zero Level

G. Tank Reference Point

H. Upper Dead Zone

I. Lower Dead Zone

K. Upper Reference Point

L. distance between Water Zero Level and mark on the upper part of the WLS

L1. Distance between the Tank Reference Point and the temperature sensor flange

L2. Distance between the mark on the top of the WLS and the temperature sensor flange

X. Level offset

R. Tank Reference Height. The distance between the Tank Reference Point and Tank Zero Level.

F

G

A

B

E

C

D

H

I

K

Содержание Rosemount 2240S



































































































































































































Отзывы:

Нет отзывов