ELTRA CS-580A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 60

background image

Installation

12

Please note: As the balance transfers the weight to the PC, its serial interface must
be programmed. This is important, if you use a balance, which was not ordered
with the analyzer.

NOTICE

For all instructions for using the PC software refer to the Help-function of the
software.

2.5 Oxygen connection

The analyzer requires two gas connections: oxygen and compressed air. The
necessary tubes for connecting the analyser to the oxygen and compressed air
supplies are shipped with the analyzer.

Fig. 4: Oxygen and air connection s– rear side of device
Tube (1) connects the oxygen supply to the analyzer on the fitting of a pressure
regulator. This connection must be very secure, considering that the incoming
oxygen pressure in the tube is 2 to 4 bar (30 to 60 psi). Do not tighten the nut too
much in order to avoid damaging of the tube. Drive the cup nut manually. Don’t use
any tool.

Fig. 2: Compressed air connection
The tube (2) connects the device through a connector with the compressor or
compressed air supply. For connecting the tube, simply push it into the connector.
This connection must be also very secure, considering that the pressure in the
compressed air is 4 to 6 bar (60 to 90 psi).

2.6 Operation modes

There are 4 different positions of the mains power switch possible:

2

1

2

«
...
10
11
12
13
14
...
»

Содержание CS-580A





























































Отзывы:

Нет отзывов

Похожие инструкции для CS-580A

Бренд: rainforest Страницы: 2

Бренд: B meters Страницы: 18

Бренд: B meters Страницы: 14

Бренд: Banner Страницы: 11

Бренд: Bante Instruments Страницы: 10

Бренд: BANTE Страницы: 11

Бренд: Banner Страницы: 14

Бренд: Banner Страницы: 16

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: NARDA Страницы: 64

Бренд: Oakton Страницы: 16

Бренд: ADA INSTRUMENTS Страницы: 27

Бренд: BD Sensors Страницы: 4

Бренд: Roland Страницы: 2

Бренд: Karman Страницы: 2

Бренд: Elcontrol Страницы: 7

Бренд: National Instruments Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды