ELTRA CS-580A Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 60

background image

Installation

16

Fig. 6: Window Configuration – Heater - Preheating
The value shows the chosen heating rate in °C/min. (The preheating function is
switched off by entering 0 in this place. Then, the heating occurs with maximum
speed after start of the UNI-software.)
3.

Save your entry with Enter.

4.

The preheating starts automatically with the next start of the software, if the

furnace temperature is lower than 100°C and the analyzer switch is at

position 2.

NOTICE

When the preheating function is activated (by any other value except 0) the
software automatically creates a shortcut at the startup menu of Windows. This
enables the start of the UNI-software with every start of the PC. The shortcut is
deleted automatically when the preheating is deactivated.

2.9.2 BIOS-configuration

In order to start the preheating before the work begins, the BIOS has to be
configured to start the PC automatically at the selected time. (The preheating starts
automatically by starting the UNI-software.)
1.

Switch on your PC and enter the BIOS by pressing the corresponding key

(e.g. F2). The normal booting process is interrupted and the BIOS menu

appears.

2.

Choose Power Management Setup

3.

Activate "Resume by Alarm" (enabled).

4.

Enter the required days and times when the heating up of the analyzer

should be started.

5.

Save your entries at Save/Exit with Yes.

6.

The booting process will be sustained.

«
...
14
15
16
17
18
...
»

Содержание CS-580A





























































Отзывы:

Нет отзывов

Похожие инструкции для CS-580A

Бренд: ParTech Страницы: 14

Бренд: janitza Страницы: 28

Бренд: IFR Страницы: 46

Бренд: VELOCICALC Страницы: 10

Бренд: Flowmetrics Страницы: 102

Бренд: TSI Instruments Страницы: 4

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: Victron energy Страницы: 46

Бренд: Kawai Страницы: 72

Бренд: Bruker BioSpin Страницы: 76

Бренд: Kabelmat Страницы: 27

Бренд: RaySafe Страницы: 2

Бренд: Keysight Страницы: 42

Бренд: Keysight Technologies Страницы: 10

Бренд: Vega Страницы: 24

Бренд: Anritsu Страницы: 15

Бренд: MONARCH INSTRUMENT Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды