ELTRA CS-580A Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 60

background image

Maintenance

32

to lift it in straight vertical direction to avoid collision of the lance (11)
with the combustion tube (12). If the assembly is not free to be easily
lifted, slightly tilt it carefully in different directions until it becomes free.

•

Unscrew the 4 screws (13) by holding the ring (14) to prevent the
combustion tube (12) from falling down.

•

Remove the ring (14).

•

Remove the O-ring (15). If this O-ring and the combustion tube
remained in the furnace after lifting the assembly (6/7), take care to
prevent the combustion tube from falling down out of the furnace. This
can be done by keeping one hand underneath the furnace or by
supporting the ring (14) with two manually driven screws (13).

•

Lift the combustion tube (12) out of the furnace top. Lift it in straight
vertical direction to avoid collision with the heating elements.

•

Place a new O-ring (9) on a new combustion tube (12).

•

Reinstall in reverse order.

NOTICE

Enter the new combustion tube very carefully in straight vertical direction to avoid
collision with the heating elements.

4.7 Lance replacing

DANGER

G0002

Mortal danger from electric shock

Exposed power contacts - High Voltage
-

An electric shock can cause injuries in the form of burns and

cardiac arrhythmia, respiratory arrest or cardiac arrest.

•

Disconnect the mains power plug before opening the

analyzer’s cabinet.

Fig. 8: Lance replacing

•

Switch off the furnace and disconnect the power plug.

•

Remove the cover panel (1) of the cabinet. Unscrew 4 screws (2) on
top.

•

Remove the tubes (3), (4) and (5) from the upper furnace closure
assembly (6/7).

«
...
30
31
32
33
34
...
»

Содержание CS-580A





























































Отзывы:

Нет отзывов

Похожие инструкции для CS-580A

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: Kane Страницы: 20

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: LATNEX Страницы: 55

Бренд: Laser Technology Страницы: 11

Бренд: Laser Technology Страницы: 62

Бренд: Omicron Lab Страницы: 33

Бренд: Omicron Lab Страницы: 21

Бренд: Omicron Lab Страницы: 22

Бренд: Vectornav Страницы: 114

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Бренд: Kawai Страницы: 8

Бренд: SOMFY Страницы: 40

Бренд: Isspro Страницы: 2

Бренд: TESTO Страницы: 2

Бренд: Kurzweil Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды