ELTEX TAU-32M.IP Скачать руководство пользователя страница 179

Страница: 179 / 334

_________________________________________________________________________________

Universal Network Terminal TAU-32M.IP 179

COMMAND LINE MODE AND TERMINAL MODE OPERATION

6.1

Basic Commands

CLI is available when the connection to the device is established via RS-232 (connection parameters: 115200,

8, n, 1, n; username:

admin

, w/o password), or Telnet/SSH.

Command descriptions are listed in Table 10. Some of commands (marked as 'priv' in 'Privilegy' column)

executing only in privelege mode (available by

enable

command). Cancel function executes opposite effect for

command or sets default value for parameter.

Table 10–List of available commands

Command

Parameter

<value>

value

Privil

egy

Description/Tip

Negotiation function

'no' command

exit

none

Stop CLI session

quit

none

Stop CLI session

help

none

CLI syntax tip

ping

<value>

IP address

none

Ping utility

repeat

<value>

number:1-
4294967295

none

Number of ping packets (default: 5)

payload

<value>

number:0-65535

none

Ping packet payload size in bytes
(default: 56)

df-bit

none

Set «don't fragment bit» (default: not
setted)

tos

<value>

number:0-255

none

Service type (default: 0)

timeout

<value>

number:1-60

none

Reply waiting time, s (default: 2)

traceroute <options>

<value>

IP address

none

TraceRoute utility

df-bit

none

Set «don't fragment bit» (default: not
setted)

repeat

<value>

number: 1-8

none

Retry amount in within one 'ttl' (defaut:
2)

timeout

<value>

number:0-10

none

Reply waiting time, s (default: 2)

ttl

<value>

number:1-255

none

Max time-to-live value (default: 255)

tos

<value>

number:0-255

none

Service type (default: 0)

icmp

none

Use ICMP ECHO instead of UDP
datagramms (default: don't use)

port

<value>

number:0-65535

none

UDP port used number (default: 33434)

size

<value>

number:40-
32768

none

Packet size in bytes (default:100)

show

none

View command

system

none

Show firmware version

hwaddr

none

Show MAC address

ipaddr

none

Show IP address

netmask

none

Show network mask

network

none

Show full network settings

version

none

Show Configuration file version

configuratio
n

priv

Show full configuration

voiceport

none

Voice ports information view

statistic

<value>

number:1-32

none

Show port statistic

status

<value>

number:1-32

none

Show port status

Содержание TAU-32M.IP















































































































































































































































































































































Результаты поиска

Содержание TAU-32M.IP

Отзывы:

ELTEX TAU-32M.IP, Руководство по эксплуатации, Страница: 179 / 334

Результаты поиска

Содержание TAU-32M.IP

Отзывы: