Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 77

Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 59

58

Parameter setting

Sensor Sewi KNX TH-L-Pr

• Version: 17.11.2016 • Technical changes and errors excepted.

A set threshold value will be retained until a new value or a change is transferred. The
current value is saved, so that it is retained in the event of a power supply failure and
will be available once the power supply is restored.

Set the

hysteresis

independent of the type of threshold value specification.

Switching output

Set the behaviour of the switching output when a threshold value is exceeded/under-
cut. The output switching delay can be set using objects or directly as a parameter.

Block

The switching output can be blocked using an object.

Threshold value setting using

Parameter •

Communication objects

Starting threshold value in 0.1% RH
valid until first communication

1 … 1000; 650

Object value limit (min.)

in 0.1%RH

1…1000

Object value limit (max.)

in 0.1%RH

1…1000

Type of threshold value change

Absolute value • Increase/decrease

Increment

(upon increase/decrease change)

0.1% RH • ... • 2.0% RH • ... • 20.0% RH

Hysteresis setting

in % • absolute

Hysteresis in 0.1% RH

0...1000; 100

Hysteresis in %
(relative to the threshold value)

0 … 50; 20

When the following conditions apply,
the output is
(TV = Threshold value)

• TV above = 1 | TV - hyst. below = 0
• TV above = 0 | TV - hyst. below = 1
• TV below = 1 |TV + hyst. above = 0
• TV below = 0 |TV + hyst. above = 1

Delays can be set via objects
(in seconds)

No • Yes

Switching delay from 0 to 1

(If delay can be set via objects:
valid until 1st communication)

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching delay from 1 to 0

(If delay can be set via objects:
valid until 1st communication)

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching output sends

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Cycle

(is only sent if periodically is selected)

5 s • 10 s • 30 s… • 2 h

«
...
57
58
59
60
61
...
»

Содержание Sewi KNX TH-L-Pr














































































Отзывы:

Нет отзывов