manualshive.com logo in svg

Elsner Sewi KNX TH-L-Pr, Инструкция по установке и настройке, Страница: 2 / 77

Поделиться
Скачать
Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 2

1

Contents

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Sensor Sewi KNX TH-L-Pr

 • from ETS programme version 1.1

Version: 17.11.2016 • Technical changes and errors excepted.

1.

Description ...........................................................................................  5

1.0.1. Scope of delivery  ..........................................................................................  6

1.1. Technical data ...........................................................................................................  6

1.1.1. Measuring accuracy ......................................................................................  7

2.

Installation and start-up .......................................................................  7

2.1. Installation notes  ......................................................................................................  7
2.2. Installation location ..................................................................................................  8

2.2.1. Coverage area of the motion detector  ........................................................  8

2.3. Construction of the sensor  ....................................................................................  10

2.3.1. Housing from the outside  ..........................................................................  10
2.3.2. Printed circuit boards / connections ..........................................................  11

2.4. Assembly ................................................................................................................  11
2.5. Notes on mounting and commissioning ..............................................................  12

3.

Addressing the equipment  .................................................................  13

4.

Maintenance .......................................................................................  13

5.

Transfer protocol  ...............................................................................  15

5.1. List of all communication objects  .........................................................................  15

6.

Parameter setting  ..............................................................................  29

6.1. Behaviour on power failure/ restoration of power  ..............................................  29
6.2. General settings  .....................................................................................................  30
6.3. Motion detector  ......................................................................................................  30

6.3.1. Master 1/2/3/4  ..............................................................................................  32
6.3.2. Align communication between master and slave ....................................  35

6.4. Light control ............................................................................................................  36
6.5. Temperature Measurement ...................................................................................  38
6.6. Temperature threshold values  ..............................................................................  39

6.6.1. Threshold value 1, 2, 3, 4  ...........................................................................  39

6.7. Temperature PI control  ..........................................................................................  41

6.7.1. Heating control level 1/2 .............................................................................  47
6.7.2. Cooling control level 1/2 .............................................................................  49

6.8. Summer Compensation .........................................................................................  51
6.9. Brightness Measurement  ......................................................................................  52
6.10.Brightness threshold values  .................................................................................  53

6.10.1. Threshold value 1/2/3/4  ..............................................................................  53

6.11.Night .......................................................................................................................  55
6.12.Humidity Measurement .........................................................................................  56
6.13.Humidity threshold values  ....................................................................................  57

6.13.1. Threshold value 1, 2, 3, 4  ...........................................................................  57

6.14.Humidity PI control  ................................................................................................  59
6.15.Dewpoint measurement ........................................................................................  62

6.15.1. Cooling medium temp. monitoring ...........................................................  62

6.16.Absolute humidity  .................................................................................................  64

Содержание Sewi KNX TH-L-Pr














































































Отзывы:

Нет отзывов