Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 77

Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 50

49

Parameter setting

Sensor Sewi KNX TH-L-Pr

• Version: 17.11.2016 • Technical changes and errors excepted.

Enter the hysteresis that prevents frequent on/off switching of temperatures in the th-
reshold range.

If separate control variables are used, select whether the control variable of the 2nd le-
vel is a 1 bit object (on/off) or an 8 bit object (on with percentage/off).

Now specify what should be sent when the control is blocked. Set a value greater 0
(=OFF) to receive a basic heating level, e.g. for floor heating. On release, the control va-
riable follows the rule again.

6.7.2. Cooling control level 1/2

If a cooling control mode is configured, one or two setting sections for the cooling le-
vels are displayed.

In the 1st level, cooling is controlled by a PI control in which either control parameters
can be entered or predetermined applications can be selected.

In the 2nd level (therefore only for 2-level cooling), cooling is controlled via a PI or a 2-
point-control.
In level 2, the setpoint deviation between the two levels must also be specified, i.e. abo-
ve which setpoint value deviation the second level is added.

PI control with control parameters:

This setting allows individual input of the parameters for PI control.

Hysteresis (in 0.1°C)

0...100; 20

Control variable is a

• 1 bit object
• 8 bit object

Value (in %)

(for 8 bit object)

0...100

When blocked, the control variable shall

• not be sent
• send a specific value

Value (in %)

only if a value is sent

0...100

Setpoint difference between 1st and 2nd
level (in 0.1°C)

(for level 2)

0...100; 40

Control type

(for level 2, no common control variables)

• 2-point-control
• PI control

Control variable is a

(for level 2 with 2-point controlling, no
common control variables)

• 1 bit object
• 8 bit object

Control type

•

PI control

Setting of the controller by

•

Controller parameter

• specified applications

«
...
48
49
50
51
52
...
»

Содержание Sewi KNX TH-L-Pr














































































Отзывы:

Нет отзывов