Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 77

Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 35

34

Parameter setting

Sensor Sewi KNX TH-L-Pr

• Version: 17.11.2016 • Technical changes and errors excepted.

Define the

output type and value

. As a result of the different types, switchable lights

(1 bit), dimmer (1 Byte 0-100%), scenarios (1 Byte 0...63 scenario call-up) and other fun-
ctions can be controlled.

Select whether delays can be set via objects and specify the

switching delays

. By set-

ting a

blocking time

after switch-off, you prevent sensors from recognising a swit-

ched-off lamp in their detection zone as a temperature change, and sending a motion
message.

Set the master's output

sending pattern

.

In addition, you can refer to a

slave signal

, i.e. a signal from an additional motion de-

tector, for controlling purposes.

Output type

• 1 bit
• 1 byte (0...255)
• 1 byte (0%...100%)
• 1 byte (0°...360°)
• 1 byte (0...63) scenario call-up
• 2 byte counter without math. symbol
• 2 byte counter with math. symbol
• 2 byte floating point
• 4 byte counter without math. symbol
• 4 byte counter with math. symbol
• 4 byte floating point

Output value in the event of motion

e.g. 0 • 1 [depending on the output type]

Output value without motion

e.g. 0 • 1 [depending on the output type]

Output value when blocked

e.g. 0 • 1 [depending on the output type]

Delays can be set via objects
(in seconds)

No • Yes

Switch on delay
(for setting via objects: valid until
1st communication)

0 s • 5 s • 10 s • ... 2 h

(for daylight dependent motion detection:
fixed value 0s)

Switch off delay
(for setting via objects: valid until
1st communication)

0 s • 5 s • 10 s • ... 2 h

Blocking time for motion detection
after switch off delay in seconds

0...600 ; 2

Sending pattern

• on change
• on change to movement
• on change to no movement
• on change and periodically
• on change to movement and periodically
• on change to no movement periodically

Cycle

(if sent periodically)

1s • 5 s • ... 2 h

Use slave signal

No • Yes

«
...
33
34
35
36
37
...
»

Содержание Sewi KNX TH-L-Pr














































































Отзывы:

Нет отзывов