Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 77

Elsner Sewi KNX TH-L-Pr Скачать руководство пользователя страница 39

38

Parameter setting

Sensor Sewi KNX TH-L-Pr

• Version: 17.11.2016 • Technical changes and errors excepted.

Set, which objects will trigger interruption and when the regulation is to be continued.

Note: If the criteria for the continuation of the regulation are fulfilled, the regulation,
however, has just been stopped by an object or is blocked, then the end of the inter-
ruption has no effect on the behaviour of the light.

The light regulation can be

blocked

via the bus. In contrast to the interruption, when

blocking, a switching command or brightness value can be sent. Upon release, the out-
put behaviour follows the rule.

6.5.

Temperature Measurement

Select, whether a

malfunction object

is to be sent if the sensor is faulty.

Use

Offsets

to adjust the readings to be sent.

The unit can calculate a

mixed value

from its own reading and an external value. Set

the mixed value calculation if desired. If an external portion is used, all of the following
settings (threshold values, etc.) are related to the overall reading.

Use interruptions

No •

Yes

Interrupt regulation when

Reception from response switching object

No • Yes

Reception from response dimming object

No • Yes

Continue regulation

• after a waiting period
• at movement after waiting period
• at object reception after waiting period
• at object reception or after waiting period
• at movement after object reception
• at object reception or movement after
waiting period

Waiting period in seconds

5...72000

(Standard value depending on the

setting of "continue regulation")

Object value

0 • 1 • 0 or 1

Use block

No •

Yes

Analysis of the blocking object

• at value 1: block | at value 0: release
• at value 0: block | at value 1: release

Value prior to initial communication

0 • 1

Output pattern

On block

• send nothing
• send off command
• send on command
• send value

Use malfunction object

No • Yes

Offset in 0.1°C

-50…50; 0

Use external measured value

No • Yes

«
...
37
38
39
40
41
...
»

Содержание Sewi KNX TH-L-Pr














































































Отзывы:

Нет отзывов