manualshive.com logo in svg

ELPRO ERRTS ALERT2, Руководство по настройке

Поделиться
Скачать
ELPRO ERRTS ALERT2 Скачать руководство пользователя страница 51

ERT-A2 ALERT2 Configuration Manual 

 

Revision 1.0 

44 

 

3.

 

Unit will indicate starting process by short flash of all four input LEDs and then progress of 
writing file with input LED scan through 1 to 4.  DO NOT REMOVE USB stick during writing 
process.  

4.

 

Completion is indicated by all four input LEDs with come on and go out. 

General Specifications 

Operation 

Modes-Topology 

Field, Repeater and Receiver station unit types 

Input and Output 

Discrete input/output 
 
 

4 digital I/O (discrete/pulsed, rain or river encoder) 
On-state voltage: <1 Vdc  
Off-state voltage: >2 Vdc 
Wetting current: 30µA 
Minimum input pulse width 1ms (active input) 

Analog Inputs 

2 single ended analog inputs configurable mA 
0-20mA current loop (under/over range) 
16 bits resolution 
Impedance < 10

0Ω 

Sensor Loop Power 

Analog:  24Vdc, max 50mA 
SDI-12:  12Vdc, max 500mA 

SDI-12 (v1.4) 

1 loop:  max of 52 configurable variables or sensors 
M or R command and CRC configurable 
Data Rate:  1200 bps, 7 data, 1 parity 

Heater Output 

Open Collector output (active close to ground) available to allow 
internal heating in very cold environments. ON @ -10

o

C OFF @ 

0

o

C, 2A max 

GPS (Optional) 

Time clock synchronization for logging/ALERT2 
GPS antenna:  SMA Female (LNA power) 

Protocols and Configuration 

 

User configuration 

Secure, user friendly, device agnostic, menu-based 
Remote (over-the-air) access:  Bluetooth BLE 
Local Access:  USB or RS232 (legacy)

 

Configurable 
Parameters 

ALERT1 (field station, receiver only), 

ALERT2™, 

field/repeater/receiver station, communications setup, unit ID, 
reporting times, input configuration, analog loop power warmup, 
date/time, SDI sensor power, logging 

RS-485 (Future) 
Note 3

 

ALERT1 input (Repeater only, ALERT2 Consolidation mode) 
ALERT2 output (Base Receiver output to decoder) 
ALERT2 redundancy (Repeater Gateway) 
Configurable 300-115200 baud/ parity/ stop  

LED Indications & Diagnostics

 

LED Indication 

Power/OK, Radio TX/RX, Config Enabled, Maintenance Mode  

Push Buttons

 

Front Panel:  Maintenance mode/Send data 
Internal Test:  Maintenance mode/send data/save logged data to 
USB/Firmware update 
Internal Boot:  Boot or Reset unit (IO values preserved) 

Reported Values

 

Содержание ERRTS ALERT2

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды