manualshive.com logo in svg

ELPRO ERRTS ALERT2, Руководство по настройке

Поделиться
Скачать
ELPRO ERRTS ALERT2 Скачать руководство пользователя страница 48

ERT-A2 ALERT2 Configuration Manual 

 

Revision 1.0 

41 

 

Radio Firmware Update 

Step 1:  Load firmware image into radio. 

h)      Load Firmware to Radio 
 
        This USB connection will go off-line for approximately 1 minute to 
        connect to the USB drive. DIO4 LED indicates loading is complete. 
        Wait for DIO4 LED to come on, then reconnect and press a key 
< DIO LEDs 1 through to 4 will light as process progresses.  Take a few minutes to load the firmware 
image into the radio> 
        Firmware Loaded to Radio 
 
DONE 
Step 2: Activate new firmware in radio. 
 
        i)      Activate Radio Firmware 
 
        Firmware Image: E2_155 radio application 1.3 9059M 20210302 
        Apply Firmware Image? (y/n):y 
        applying ... 
        Firmware Loaded to Radio 
 
Complete, check radio firmware version is updated with option f. 
 
 

Cellular Modem Force Update Messaging 

Power UP modem 
Wait for modem power up 
Modem ON. Time since PWR = 150172; RxChars=0 
Waking modem... 
AT 
OK 
 modem awake 
  ==>AT+CREG? 
+CREG: 0,1 
OK 
AT+CREG? 
+CREG: 0,1 
OK 
Modem connected, Network Status=1 
  ==>AT+CSQ 
+CSQ: 26,99 
OK 
AT+CSQ 
+CSQ: 26,99 
OK 
Raw RSSI=26; Decoded=-61dBm 
Correct for time delay = 2 seconds 
  ==>AT+QIOPEN=1,0,"TCP","10.255.40.17",31000,0,2 

Serial comms to Cell Modem Ok, if modem does 
not respond then ensure Radio Mobile Module is 
enabled in cell modem 

Connection made to cellular network, if this fails 
then check IP and port settings 

Содержание ERRTS ALERT2

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды