manualshive.com logo in svg

ELPRO ERRTS ALERT2, Руководство по настройке

Поделиться
Скачать
ELPRO ERRTS ALERT2 Скачать руководство пользователя страница 25

ERT-A2 ALERT2 Configuration Manual 

 

Revision 1.0 

18 

 

o

 

Supply monitoring (battery/supply in) 

o

 

RSSI, temperature, internal faults 

Base Receiver Station 

The base receiver station configuration mode is used for the 
collection of ALERT2 or legacy ALERT1 data at the network access 
point.  It is normally used in conjunction with the 115E-2-A2 Decoder-
Gateway unit. 

Base receiver units are usually located very close to the receiving 
antenna to ensure shortest RF cable can be used and connects to the 
115E-2-A2 decoder-gateway unit using a RS-485 link (twisted pair).    

The 115E-2-A2 then receives this RS-485 data and allows host devices 
to connect via TCP to a standard ethernet connection.  The decoder-
gateway can also be used to accept legacy ALERT1 protocol through 

its RS-232 port to connect to existing ALERT1 decoders.  

The ERT-A2 base receiver can also be installed with a RF splitter-combiner to allow single antenna to 
be shared between legacy ALERT1 system and the ALERT2 protocol unit.  The 115E-2-A2 allows both 
connections and conversion of ALERT1 to ALERT2 as a concentration frame. 

Capability Summary: 

-

 

Base station receiver VHF/UHF radio 

-

 

RS-485 A2 data provides a medium distance connection up to 1km (4000ft) to decoder 
configurable data rate. 

-

 

Output communications can be either RS232 or RS485 could support ALERT2 Binary modes 

-

 

Decoder-Gateway connects RS-485/232 A2 data to Ethernet, HFEM, HyData, ALERT1 or 
converts into industrial protocols such as Modbus or DNP3 for Environmental or Industrial 
applications  

-

 

Internal IO diagnostics: 

o

 

Supply monitoring (battery/supply in) 

o

 

RSSI, temperature, internal faults 

Repeater Station 

–

 Full Duplex High Capacity 

Repeater and receiver units can be linked using 
the RS-485 interfaces which allows several useful 
configurations to be formed to solve more 
complex network design challenges. 

For very large systems the backbone of the 
network data frame capacity can be increased 
twofold by using a second radio frequency and 
running in a full duplex mode.   

The repeater will aggregate ALERT2 data frames 
when there is very high incoming data flows to 
achieve the most efficient use of radio channel. 

Содержание ERRTS ALERT2

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды