background image

56

User Manual 

MN032EN

Effective October 2017

215U-2 802.11 

wireless I/O and gateway 

  

EATON

 www.eaton.com

3.  You may copy and distribute the Program (or a work based on 

it, under Section 2) in object code or executable form under the 

terms of Sections 1 and 2 above provided that you also do one 

of the following: 
a.  Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the 

terms of Sections 1 and 2 above on a medium customarily 

used for software interchange; or, 

b.  Accompany it with a written offer, valid for at least three 

years, to give any third party, for a charge no more than your 

cost of physically performing source distribution, a complete 

machine-readable copy of the corresponding source code, to 

be distributed under the terms of Sections 1 and 2 above on 

a medium customarily used for software interchange; or, 

c.  Accompany it with the information you received as to 

the offer to distribute corresponding source code. (This 

alternative is allowed only for noncommercial distribution and 

only if you received the program in object code or executable 

form with such an offer, in accord with Subsection b above.) 

The source code for a work means the preferred form of 

the work for making modifications to it. For an executable 

work, complete source code means all the source code 

for all modules it contains, plus any associated interface 

definition files, plus the scripts used to control compilation 

and installation of the executable. However, as a special 

exception, the source code distributed need not include 

anything that is normally distributed (in either source or 

binary form) with the major components (compiler, kernel, 

and so on) of the operating system on which the executable 

runs, unless that component itself accompanies the 

executable. 
If distribution of executable or object code is made by 

offering access to copy from a designated place, then 

offering equivalent access to copy the source code from the 

same place counts as distribution of the source code, even 

though third parties are not compelled to copy the source 

along with the object code. 

4.  You may not copy, modify, sublicense, or distribute the Program 

except as expressly provided under this License. Any attempt 

otherwise to copy, modify, sublicense or distribute the Program 

is void, and will automatically terminate your rights under 

this License. However, parties who have received copies, or 

rights, from you under this License will not have their licenses 

terminated so long as such parties remain in full compliance. 

5.  You are not required to accept this License, since you have not 

signed it. However, nothing else grants you permission to modify 

or distribute the Program or its derivative works. These actions 

are prohibited by law if you do not accept this License. Therefore, 

by modifying or distributing the Program (or any work based on 

the Program), you indicate your acceptance of this License to do 

so, and all its terms and conditions for copying, distributing or 

modifying the Program or works based on it. 

6.  Each time you redistribute the Program (or any work based on 

the Program), the recipient automatically receives a license from 

the original licensor to copy, distribute or modify the Program 

subject to these terms and conditions. You may not impose 

any further restrictions on the recipients’ exercise of the rights 

granted herein. You are not responsible for enforcing compliance 

by third parties to this License. 

7.  If, as a consequence of a court judgment or allegation of patent 

infringement or for any other reason (not limited to patent 

issues), conditions are imposed on you (whether by court order, 

agreement or otherwise) that contradict the conditions of this 

License, they do not excuse you from the conditions of this 

License. If you cannot distribute so as to satisfy simultaneously 

your obligations under this License and any other pertinent 

obligations, then as a consequence you may not distribute 

the Program at all. For example, if a patent license would not 

permit royalty-free redistribution of the Program by all those who 

receive copies directly or indirectly through you, then the only 

way you could satisfy both it and this License would be to refrain 

entirely from distribution of the Program. 
If any portion of this section is held invalid or unenforceable 

under any particular circumstance, the balance of the section is 

intended to apply and the section as a whole is intended to apply 

in other circumstances. 
It is not the purpose of this section to induce you to infringe any 

patents or other property right claims or to contest validity of 

any such claims; this section has the sole purpose of protecting 

the integrity of the free software distribution system, which 

is implemented by public license practices. Many people have 

made generous contributions to the wide range of software 

distributed through that system in reliance on consistent 

application of that system; it is up to the author/donor to decide 

if he or she is willing to distribute software through any other 

system and a licensee cannot impose that choice. 
This section is intended to make thoroughly clear what is 

believed to be a consequence of the rest of this License. 

8.  If the distribution and/or use of the Program is restricted in 

certain countries either by patents or by copyrighted interfaces, 

the original copyright holder who places the Program under this 

License may add an explicit geographical distribution limitation 

excluding those countries, so that distribution is permitted only 

in or among countries not thus excluded. In such case, this 

License incorporates the limitation as if written in the body of 

this License. 

9.  The Free Software Foundation may publish revised and/or new 

versions of the General Public License from time to time. Such 

new versions will be similar in spirit to the present version, but 

may differ in detail to address new problems or concerns. 
Each version is given a distinguishing version number. If the 

Program specifies a version number of this License which 

applies to it and “any later version”, you have the option of 

following the terms and conditions either of that version or of 

any later version published by the Free Software Foundation. If 

the Program does not specify a version number of this License, 

you may choose any version ever published by the Free Software 

Foundation. 

10. If you wish to incorporate parts of the Program into other free 

programs whose distribution conditions are different, write to the 

author to ask for permission. For software which is copyrighted 

by the Free Software Foundation, write to the Free Software 

Foundation; we sometimes make exceptions for this. Our 

decision will be guided by the two goals of preserving the free 

status of all derivatives of our free software and of promoting the 

sharing and reuse of software generally. 

Содержание 215U-2
































































Отзывы: