background image

Ness

-M1XEP  Installation Manual 

Page 9

The "Email" tab is where information regarding email notification is stored.

a.

Enter the SMTP server’s URL or IP address.  This can be up to 48 characters long.  Set the port value to the
correct setting for outgoing mail.  The default port setting is 25.  If your mail server uses a different port, your
Internet service provider or network administrator can provide you with the correct port setting.

b.

Some Internet Service Providers will block email if it is not sent from a valid email account.  Enter a valid
email address in the “FROM” email address block.  This is the address that will appear in the “from” field of
the email.

c.

Some Internet Service Providers may require a username or password to log onto the email server.  If
required, enter the username and password in the corresponding fields.  If your Internet Service Provider does
not require  this log on information, leave the fields blank.  

The email authentication fields are supported only

by M1XEPs with firmware version 1.2.0 or later.

d.

The lower portion of this screen is where the email addresses and messages for email notification are
entered.  Up to 16 addresses and messages can be stored.  Email addresses can be up to 48 characters
long.  The message body may be up to 255 characters long.  To enter an email address, simply click on the
line where you want to enter the address and type the address.  Then click on the message block next to
the address and enter the message that you want to be sent to that address.  These messages are
activated using the Whenever/And/Then rules programming in 

Ness

RP.

4.  Email Notification Setup (optional)

Send changes to the M1XEP and save the changes to the database.  Refer to section 2 on page 8.

Rule Example

The following is an example of a rule that will send an email message.  In this example, an email message will be
sent when the system is disarmed by a particular user.  This email is sent to "Mom" at the office to let her know
Little Suzy got home okay.

WHENEVER Smith Home (Area 1) STATE BECOMES DISARMED

AND LAST USER WAS Suzy Smith (User 3)

THEN SEND EMAIL MESSAGE 1 TO [email protected] (Email 1)

Содержание Ness M1XEP

























Отзывы: