manualshive.com logo in svg

Eliet MA 018 010 130, Руководство пользователя

Поделиться
Скачать
Eliet MA 018 010 130 Скачать руководство пользователя страница 33

33

English

9.7.4 Engine stops from lack of fuel

Due to inattentiveness, engine has ran out of fuel whilst running, and has stopped. 

Restarting the engine.

• Remove the safety cover on the right-hand side (see 11.3.2).

• Fill the diesel tank (see 9.2).

• Manually bleed the fuel lines and the fi lter. To this effect, a priming 

pump (3) is provided on the fuel fi lter (repeatedly press and release the 

button on top of the diesel fi lter).

• Refi t the safety cover.

• Start the engine.

9.7.5 Engine no longer runs and the machine must be moved.

Since the hydraulic pump is powered by the diesel engine, in the event of a defective engine, all 

hydraulic functions are lost. The wheel drive is also hydraulic. How can you still move the heavy 

machine in this situation ?

You can try to push the machine a short distance on fl at, hard ground. However, the following 

recommendations must be observed :

• This action involves at least 2 persons.

• Move the black control lever for the feed mechanism to the “Stop” position.

• Fold down the handlebar to the transport position and lock this using the pin.

• Turn the handle on the handlebar and push the machine forwards at the same time.

• You will probably fi nd it diffi cult to move the machine. You will encounter resistance from the 

hydraulic drive components.

If the distance is too great, or if the ground is uneven, you can disconnect the wheels from the 

drive system. After doing this, the machine will offer less resistance and can also be towed by 

another vehicle.

Proceed as follows.

• Support machine underneath a fi xed and robust part of the chassis. Make sure that the support 

cannot sink into the ground.

• Remove the wheel (see 11.4.3).

• You can now remove the small driven gearwheel (1). To do this, unscrew the M8 securing bolt (13 

mm spanner) and slide the gearwheel off the shaft (if necessary, with the help of a crowbar).

• Refi t the wheel onto the hub and fi rmly tighten it.

• Repeat the procedure for the other wheel.

• Make sure that the machine is always fi rmly supported so that it does not tip over.

Содержание MA 018 010 130






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды