Electrolux Combi TOUCH Series Скачать руководство пользователя

Страница: 63 / 68

Anom-
aly

Type of
anomaly

Description

Possible causes

Actions

HFnI

Stops
humidifier

Humidifier not working

• Water missing;
• ISG circuit obstruction.

The oven has detected a problem with the
humidifier (ISG). It is only possible to cook in
convection mode.
Verify the water supply valve is fully open and
the water filler has no obstructions. Clean it if
needed.
If the problem persists, call Service.

Htd

Stops oven

Drain temperature
above safety limit

Possible lack of water in the
drain system.

• Check that the oven has water supply;
• Pour some water on the bottom cavity filter;
• Wait for the alarm to blink off;
• If the problem persists, call Service.

LPIn

Stops cycle

Boiler level sensor
problem

• Humid lime shortcutting

boiler level sensors.

• Insulation issues with the

boiler level sensors

The oven can continue to operate in convection
or in ISG mode.

• There is a problem with the water level in the

boiler: run a cleaning program including the
rinse and descale cycle and use 2 tabs C25
only. (Follow the procedure as per User
Manual);

• If the problem persists, call Service.

MCbM

Stops oven

Lower inverter commu-
nication problem

• Issue with the motor

inverter;

• Connection or electrical

issue

Communication error with lower cavity motor
inverter.

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

MCtM

Stops the
oven

Upper inverter commu-
nication problem

• Issue with the motor

inverter;

• Connection or electrical

issue,

Communication error with upper cavity motor
inverter.

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

PFAC

Stops oven

Factory parameters
map corrupted

Issue with the SW or with
the HW

• Try to switch the oven OFF/ON.
• If the problem persists, call Service.

SbbU

Stops
boiler gas

Boiler gas fan speed
issue

• Burner blower motor

overload due to dirt or
oxidation

• Other electrical/mechani-

cal issue

Burner fan does not reach the desired speed.
Call Service.

SbCd

Stops cycle
Stops
cycle/
convection

Cavity lower gas
burner blower speed
issue

• Burner blower motor

overload due to dirt or
oxidation;

• Other electrical/mechani-

cal issue.

Burner fan does not reach desired speed.
Call Service.

SbCU

Stops
cycle/
convection

Cavity upper gas
burner blower speed
issue

• Burner blower motor

overload due to dirt or
oxidation;

• Other electrical/mechani-

cal issue.

Burner fan does not reach desired speed.
Ovens with boiler can cook in 100

℃

steam

mode. To restore full oven functionality call
Service.

SLUS

Stops
boiler
cycles

Water boiler working
level not reached in
time

• Water supply valve

closed or partly closed;

• Temporary lack of water

supply pressure;

•

Boiler water level sensor

failure;

• Boiler leakage: drain

valve or fracture.

• Ensure the water supply valve is fully open

and the water filter has no obstructions. Clean
it if needed;

• The oven can continue to work in Convection

mode;

•

Unless the water is missing from the mains,

the oven can continue to work in recovery
mode

• Call Service to restore boiler functionality.

If the fault persists after carrying out the above checks, contact the Customer Care Service, remembering to specify:

A. the type of fault;
B. the appliance PNC (production number code);
C. the Ser. No. (appliance serial number).

Содержание Combi TOUCH Series





































































Результаты поиска

Содержание Combi TOUCH Series

Отзывы:

Похожие инструкции для Combi TOUCH Series

Бренды по названию

Популярные бренды

Electrolux Combi TOUCH Series, Руководство пользователя

Результаты поиска

Содержание Combi TOUCH Series

Отзывы:

Похожие инструкции для Combi TOUCH Series

Бренды по названию

Популярные бренды