25
Delete the Preset
• Additional actions on the program can be done through the
lower drawer. Open the lower drawer to:
Save all presets
Save all preset instead of saving them one by one.
Clear all presets
Delete all presets instead of deleting them one by one.
Save MT program
Save all the presets as a MultiTimer program.
Reload Presets
Available only in a MultiTimer program, it allows to
reload the deleted presets of a MT program.
Reload MT programs
It allows to load again a MT program.
4.
Touch the button
to start the cycle. The preheating
starts.
5.
Insert the food in the oven, the core probe in the product
(when needed) and close the door to start the cycle.
The screen saver shows up to three presets: the remaining
time (or the current food core temperature) and the name,
when present. The presets are ordered from top to bottom
according to minimum and maximum remaining time.
6.
When a preset ends, some acoustic signals sound. The
display shows the MultiTimer page list with the ended
preset blinking in green. Open the door and remove food.
After closing the door, the ended preset disappears from
display.
NOTE!
During a preset it is possible to add other presets.
The preset reference number blinks while the door is
open to insert the food in the appliance. When the
door is closed again the preset reference number
stops blinking.
7.
When the last preset ends and the food is removed, hold
down the button
to stop the preset cycle.
MULTIPHASE DRAWER
Food can be cooked with different modes during its cycle and
therefore in different phases.
The oven enables programmes consisting of several sequential
phases (up to a maximum of 16 phases).
During a programme, going from one phase to the next occurs
automatically. The program automatically stops when all phases
are completed.
How to set the Multiphase programme
1. Set first a cooking cycle, (refer to F.5
paragraph);
2. Add a new phase;
There are two ways to add a phase:
• Touch the “+“ icon in the Multiphase Drawer;
The appliance adds further phases. Touch the Multiphase
Drawer to check the phase list.
Touch each phase row to assign new parameters.
• Open the Multiphase Drawer and touch “Add cycle“ icon.
Add Cycle
Touch this icon to add a new phase.
The oven adds default phases. Touch the phase row to
set new parameters.
Add Pause
Touch this icon to add the Pause phase.
Add Hold
Touch this icon to add the Holding phase.
The default temperature of the Holding phase is 70
℃
, if
necessary, touch the corresponding row to change it.
NOTE!
The HOLD phase appears always at the end of
the list and cannot be moved and copied.
It is possible to add a maximum of 16 Hold phase.
1
2
3
4
5
6
7
8
9
10
Leand ro
PreA
Nome
Nome
Nome
Nome
Nome
Nome
Nome
Leand ro
1:00
--:--
--:--
--:--
--:--
--:--
--:--
--:--
1:00
2:00
PreA
PreC
PreD
PreB
PreE
PreG
PreH
PreI
PreF
CHEF 1
MAN UAL
1
2
3
5
6
7
10
8
9
4
MultiTimer
10:30m:s
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
--:-- h:m
PreA
----
----
----
----
----
----
----
----
----
PM
5:30
100%
120°C
300°C
Restore
MT
program
Save all
presets
Clear all
presets
Save MT
program
MANUAL
USER
:
0 50
: 9
5
1
Jacket potatoes
Grilled mixed vegetables
0029
:
:59
°C
50
Quiche lorraine
75°C
MANUAL
1
2
3
MultiTimer
h:m
50 C°
Jacket potatoes
Quiche Lorraine
00:29
01:50
h:m
Grilled mixed
50
%
1
USER
MANUAL
00:30
:00
25
C
°
50
%
1
USER
MANUAL
00:30
:00
25
C
°
2
3
25
°C
0030
:
:00
00:30 h:m
160°C
50%
20
%
+
+
+
00:30 h:m
50 %
7
160 °C
1
Multiphase
Cycle
Pause
Hold
MANUAL
50
%
1
MANUAL
00:30
:00
25
C
°
+
+
+
