manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Руководство по обслуживанию

Поделиться
Скачать
EFI FIERY X3eTY 35C-KM Скачать руководство пользователя страница 66

58

The troubleshooting process

Symptoms and solutions

Look in these charts for the various problems and possible actions. To learn possible 
causes and solutions for a specific error condition, find the symptom in the charts and 
perform the appropriate suggested actions in the order listed in the numbered steps. 
Verify functionality after each numbered step. Proceed to the next numbered step only if 
the problem persists. For example, in the steps:

1.

Check and reseat the copier interface cable between the Fiery X3eTY and the copier.

2.

Replace the copier interface cable.

Perform step 1 and then verify functionality. If the problem is resolved, do not perform 
step 2.

T

ABLE

 A

Fiery X3eTY error conditions 

Symptom

Possible cause

Suggested action 

Startup

Both the copier power 
switch and Fiery X3eTY 
power switch are in On 
position, but the 
Fiery X3eTY does not 
start up

One of the following:

• Faulty cable 

connections

• Fiery X3eTY is 

stalled in an incorrect 
power state

1. Check again all cables and connections. Make sure that the copier is 

connected to a power source.

2. Power off/on the copier.

3. Power off/on the Fiery X3eTY using the Fiery X3eTY power switch.

4. Firmly press the Fiery X3eTY soft power button once for two seconds and 

then release.

If the problem persists, contact your authorized service/support provider.

Fiery X3eTY starts up 
then shuts down

One of the following:

• Print engine is 

powered off

• Fiery X3eTY is 

powered off

• Faulty connection 

between Fiery  X3eTY 
and copier

• Faulty power supply

• Faulty motherboard

• Faulty CPU

• Faulty copier 

interface board

1. Make sure both the copier power switch and the Fiery X3eTY power switch 

are in ON position.

2. Check and reseat the copier interface cable between the Fiery X3eTY and 

the Fiery X3eTY.

3. Replace the copier interface cable.

4. Listen for the power supply fan and feel for air near the Fiery X3eTY 

power switch where the power supply is located.

If you do not feel air from the power supply fan, you may have a faulty 
power supply which you must replace.

5. Clear the CMOS and power-up settings (see page 72).

6. Replace the motherboard.

7. Replace the CPU.

8. Replace the copier interface board.

Содержание FIERY X3eTY 35C-KM



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды