manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Руководство по обслуживанию

Поделиться
Скачать
EFI FIERY X3eTY 35C-KM Скачать руководство пользователя страница 34

26

Removing and replacing components

4.

Replace the CPU cooling assembly:

5.

Connect the CPU fan cable to the motherboard connector FAN1. 

If you are installing a new CPU, secure the slack in the fan cable using a tie-wrap 
(if necessary). The tie-wrap prevents the fan cable from interfering with the CPU fan. 
Also, make sure the connector on the cable is securely connected to connector FAN1 
on the motherboard.

6.

Reassemble the Fiery X3eTY and verify its functionality (see page 34).

• Make sure the levers on the

clamp are in the open position 
(spine up).

• Align the heatsink so that the fan 

cable is near the CPU fan 
connector on the motherboard 
FAN1. 

• Place the heatsink on the CPU 

and inside the bracket. 

Make sure the heatsink is fully 
seated in the bracket on all sides.

• Press down on the clamp until all 

four hooks engage the slots in the 
bracket. 

Avoid using excessive force when 
pressing down on the clamp. 

• Close the levers simultaneously.

Closing the levers simultaneously 
applies clamping force equally 
over the CPU and bracket.

Bracket

Clamp

Hooks

(2 of 4)

Lever open

Lever open

CPU

Heatsink

Slot
(1 of 4)

Engage all four hooks,
and then close both 
levers simultaneously

Lever closed

Lever closed

Содержание FIERY X3eTY 35C-KM



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды